Requirements
- Mounting and electrical connection of the charging station have been completed by a qualified electrician in accordance with local installation regulations (wall mounting at 0.9–1.5 m height, upstream circuit breaker, upstream residual current device of at least type A).
- The charging station firmware is up to date (neoom CONNECT requires at least version V60.4).
- The go-e app is installed (integrator smartphone or customer smartphone)
- The supplied reset card is available (serial number, hotspot SSID, hotspot password, QR code).
- First self-test
After proper mains connection and switching on, the charging station automatically performs a self-test at the first start (and after every restart). The LED ring briefly lights up in rainbow colors. After that, the charging station is generally ready to charge; basic functions also work without the app/backend.
- Connecting to the charging station (hotspot)
- Open the go-e app and select "Set up device" to start commissioning.
- Connect to the hotspot of the charging station:
- Option A: Scan the QR code on the reset card.
- Option B: Manually connect to the network "go-e-xxxxxx" in the smartphone's Wi-Fi settings, enter the password "Hotspot Key" from the reset card, then return to the app.
- Alternatively, for large-scale rollouts (multiple sites/devices): commissioning via the go-e portal using the serial number and the default password of the reset card, without a direct hotspot connection (LTE/Ethernet).
- Grid and charging settings
- Select the country to apply the country-specific grid default settings.
- Set the maximum charging current:
- Default: 16 A (corresponds to 11 kW with a three-phase connection).
- For 22 kW: set the maximum charging current to 32 A (only possible if the electrical installation can deliver three-phase 32 A per phase; not possible with the 11 kW variants CH-PRO-CABLE-011 / CH-PRO-CABLE-ME-011). The 22 kW variant is expected to be available from Q1 2027 at the earliest.
- When changing the default power: set a technician password to protect the setting.
- Setting up the network or Wi-Fi connection
- If no network cable is connected: select the Wi-Fi network and enter the password (or manually add SSID + password if the network is not listed).
- Optional: change the default password of the charging station (from the reset card) for security reasons.
- Disconnect from the hotspot and switch the smartphone back to its normal internet connection.
- neoom-specific: Integration into neoom Ai
In addition to the general go-e commissioning, the following steps are required for the neoom integration (for details see the article "Integrating the go-e Charger PRO (neoom edition) charging station"):
- Bring the firmware to at least version V60.4.
- In the go-e app under "Advanced settings":
- "Allow local Modbus TCP API" → ON (already set at the factory for the neoom edition)
- "Swap registers" → ON (already set automatically by the BEAAM)
- "Swap bytes" → OFF (already set automatically by the BEAAM)
- If necessary, assign a static IP address to the charging station in the customer's router settings (recommended if the charging station is not in the BEAAM network; otherwise the IP may change after a few weeks and the charging station can no longer be reached in neoom CONNECT).
- In neoom CONNECT (connect.neoom.com), add a new device at the site under "Site configuration" via "+ Tile": IP address, port 502, unit ID 1.
- After saving, click "Apply configuration".
- Storing the reset card
The reset card contains the serial number, hotspot SSID, hotspot password and QR code and should be kept in a safe place that is quickly accessible to the customer. With it, the charging station can be reset to factory settings at any time by holding it in front of the RFID reader (stored RFID chips and consumption data are retained).
Please note that the network and communication settings then have to be set up again! Details in the following article: go-e Charger PRO (neoom edition) - what needs to be reconfigured after using the RESET card?
- Status check after commissioning
The LED ring indicates the operating state, including:
- Ready to charge: blue LEDs corresponding to the set charging current.
- Waiting for vehicle: yellow LEDs.
- Charging in progress: rotating light ring (1 "tail" = single-phase, 3 "tails" = three-phase).
- Charging completed: LEDs light up green.
Sources
- go-e Charger PRO CABLE / CABLE ME - Installation and operating instructions, V1.0 (go-e GmbH), chapters 7 "Installation" and 8 "Commissioning": <https://go-e.com/fileadmin/Support/Anleitungen/Deutsch/go-e-charger-pro-installations-und-bedienungsanleitung.pdf>